Bloomfield Hills Garage Door Co
Our technician in plain workwear kneeling beside a sectional garage door with one lower section removed, the opening and neighboring panels visible, bright daylight

Panel replacement · Bloomfield Hills, MI

Garage Door Panel Replacement in Bloomfield Hills

Cracked, bent or dented sections swapped so the door closes flat, lifts evenly and looks right from the driveway. We come to you, look at the damage, and tell you whether the panel can be fixed or needs to be replaced.

CALL NOW: (248) 975-7351
  • Licensed and insured
  • Upfront quote before work begins
  • Parts-and-labor warranty

Panel replacement

Garage door panel replacement starts with how the door was hit

A sectional garage door is a stack of hinged panels, and each one carries part of the door's strength. When a panel is cracked, creased or pushed out of shape, the door stops rolling cleanly. The rollers bind, the seal along the bottom no longer sits flat, and the neighboring panels start to twist.

Most damage comes from a few familiar causes: a car bumper nudging the door, a basketball or snow shovel, ice that froze to the bottom edge and tore the section when the door was forced, or a door that was run while a track problem was bending it. A small dent in a heavy steel or insulated panel is often cosmetic. A crease across the panel, or a dent that sits on a hinge or roller location, is a structural problem, and a dent that has stretched the metal usually cannot be pulled out and look right.

That is the first thing we sort out. Some people searching for dent repair only need the damage to stop getting worse. Others need a fresh section. We look at the door, tell you which it is, and explain why.

CALL NOW: (248) 975-7351
Our technician in plain workwear pressing a gloved hand along a dented steel garage door panel to check how deep the crease runs, daylight

What we check

What we check before deciding to replace a panel

How deep the dent is

A shallow dent in the middle of a flat section can often be left alone or smoothed. A sharp crease, or metal that has stretched, will not pull back out and keeps the panel weak.

Where the damage sits

Damage near a hinge, a roller bracket or a joint between sections affects how the door moves. We check those points because a panel that looks fine from the street can still bind in the track.

Whether a matching panel exists

Panels come in set widths, heights, colors and surface patterns. We check that a replacement section will line up with the rest of the door. If the design is no longer made, we explain the options, including replacing the whole door.

Door weight and balance

An insulated section weighs more than a plain steel one. When a heavier or lighter panel goes in, the springs may need a fresh look so the door still stays put halfway up.

Reinforcement and fit

Wide doors rely on horizontal struts for stiffness. We check that the new section takes the same struts, hinges and weather seal, so the door runs straight.

CALL NOW: (248) 975-7351

How it works

How a panel replacement job goes

  1. 01

    You tell us what happened

    Describe the damage and what the door does now. Does it still go up and down, does it scrape, is it hanging crooked? That tells us what to bring.

  2. 02

    We come out and look

    Our uniformed technician checks the panel, the hinges, the rollers and the tracks, and tells you what the damage has done to the rest of the door.

  3. 03

    We explain the fix and the price

    You get an upfront quote before any work begins, and we explain whether the section can be repaired or has to be replaced. The price depends on the door's size and type, the panel itself and what else the damage touched.

  4. 04

    We swap the section

    The old section comes out, the hinges and hardware move to the new one, struts go on, and we run the door through its full travel to check it is level and sealing. Repairs and installations are backed by a parts-and-labor warranty.

CALL NOW: (248) 975-7351

Damaged panels

Dented, creased or cracked section? Tell us what the door looks like and what it does, and we will tell you what it likely needs.

CALL NOW: (248) 975-7351

Our work

Panel replacement, from damaged section to finished door

A white sectional garage door with an even, uniform set of panels closed on a brick house in daylight
A matching set of panels after replacement
Close-up of a garage door hinge joining two panels with the roller wheel visible in the track, plain steel
Hinges move to the new section
Our technician in plain workwear lifting a replacement garage door section into place from inside the garage
Fitting the new section

FAQ

Questions about panel replacement and dent repair

Can a dented garage door panel be repaired, or does it need replacing?
A shallow dent that has not creased the metal can often be left or improved, and a sharp crease or stretched steel cannot. We look at the depth, the location and whether the dent touches a hinge or roller point before saying which. If the door still runs smoothly, a cosmetic dent is your call to make.
Will a new panel match the rest of my door?
Usually yes, if the door's design is still made, but color and surface finish can vary with age and sun. We check the profile and color before ordering and tell you honestly how close it will look. When a match is not possible, we go over what a full garage door installation would involve.
Can I keep using the door with a damaged panel?
Only if it still moves smoothly and the damage is cosmetic. A cracked or folded panel can bind in the track, and forcing it can bend the track or pull a cable off. If the door scrapes, shudders or hangs crooked, stop using it and leave it closed if you can.
What decides the price of a panel replacement?
The door's size, whether it is steel, insulated or another material, the panel itself, and how much else the damage affected. We give you the number in an upfront quote before any work starts, so you decide with it in front of you.
How long does a panel swap take?
A single section is usually a one-visit job once we have the right panel. The wait, if there is one, is getting a matching section, and we tell you what to expect when we have looked at the door.
Do the springs need attention when a panel is replaced?
If the new section is heavier or lighter than the old one, the door's balance can shift. We check that the door stays in place halfway up, and a worn or mismatched spring gets sorted out in the same visit.
What should I have ready when I call?
Tell us where the damage is, how it happened and whether the door still opens and closes. A rough width of the door and its color help us plan, and we confirm everything when we see it.

Call us

Bent or damaged panel on your garage door?

Tell us what hit it and how the door is running now. We will come out, check the damaged section and the parts around it, and explain the fix and the quote before any work starts.

CALL NOW: (248) 975-7351
  • Licensed and insured
  • Upfront quote before work begins
  • Parts-and-labor warranty